Browse all practice questions for the Hazardous Materials 6th Edition Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Hazardous Materials 6th Edition Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • Which of the following statements is true about pressure relief devices?
  • Which division corresponds to toxic gases?
  • Placard color orange indicates which hazard?
  • Which two-letter code indicates that the material is an oxidizer?
  • In a hazmat incident, which zone is the clean area for command, staging, medical, and administrative activities?
  • At which pH is a solution neither acidic nor basic?
  • Which process is gas to liquid?
  • A gas with water capacity 950 pounds is which category?
  • What hazards do organic peroxides present, and what handling precautions are typically required?
  • Which statement about atmospheric pressure at sea level is accurate?
  • Which material spontaneously decays and releases radiation?
  • Which division corresponds to flammable solids?
  • Which of the following best describes the Globally Harmonized System (GHS)?
  • Under GHS, what is the purpose of standardized pictograms?
  • Which statement best defines gross decontamination?
  • What is the purpose of a decontamination corridor, and what steps occur there?
  • Bulk liquid is defined as more than how many gallons?
  • A solid with mass 880 pounds is which category?
  • Which of the following is a TRACEMP hazard category?
  • Which division corresponds to spontaneously combustible materials?
  • Placards must appear on which sides of the packaging?
  • Minimum temperature to which a fuel other than a liquid in air must be heated in order to start self sustain combustion independent of the heating source.
  • What instrument types are used to detect and measure radiation in hazmat scenes, and what are their limitations?
  • What unique hazards are associated with radioactive materials at hazmat scenes, and what basic protective principles apply?
  • What does a P following the guide number indicate?
  • Which instrument measures several gases at once but may not identify unknowns?
  • What is the weightless packet of electromagnetic energy such as x-rays called?
  • What minimum temperature at which a liquid gives off enough vapors to form an ignitable mixture with air near the surface of the liquid?
  • What basic steps should responders take if there is a potential biological hazard at a hazmat scene?
  • Explosive hazard placard color is which?
  • How is the Emergency Response Guidebook (ERG) used at the scene of a hazmat release, and what are its limitations?
  • Which container type is commonly used for bulk liquids in HazMat transport, with an example such as a tote?
  • What is the term for a large class or plastic bottle that may be in case in a basket or box?
  • Who should be notified when there is a potential biological hazard at a hazmat scene?
  • A fire hazard material with no explosive hazard belongs to which division?
  • Which of the following is NOT a dispersion pattern for liquid holding containers?
  • What is the role of the Emergency Response Guidebook (ERG) in hazmat incidents?
  • In a small contained hazmat spill that is not TIH, which action is appropriate?
  • Which statement best differentiates MSDS from SDS?
  • Which division corresponds to Toxic Substances?
  • What is the sequence for decontamination of a patient who has entered the warm zone?
  • A nonpressurized insulated container that has a vacuum space between the outer shell and inner vessel is known as what?
  • What is the capacity range of cryogenic liquid tanks?
  • What is the HazMat Branch's role within the Incident Command System (ICS) at a major incident?
  • Which radiation is an electromagnetic wave that does not consist of particles?
  • The term describing responders who perform offensive hazmat operations.
  • Shelter-in-place is preferred over evacuation when which condition is met?
  • Which division is associated with a mass explosion hazard?
  • Which of the following is NOT a common stressor for pressure containers?
  • Which factor is explicitly cited as guiding PPE decisions when the product identity is unknown?
  • Which option correctly matches a hazard class with an example?
  • Toxic Substances are classified under which division?
  • What is the standard atmospheric pressure at sea level in psi?
  • Non-pressure atmospheric storage tanks are capable of holding contents at what pressure?
  • Which hazard is described as dangerous when wet?
  • Which of the following is NOT a dispersion pattern for pressure containers?
  • Which of the following is NOT a dispersion pattern associated with pressure containers?
  • Which division is described as extremely insensitive explosives?
  • Which items are typically included in an after-action report following a hazmat incident?
  • Bulk gas is defined as water capacity greater than what pounds?
  • Which term refers to a large class or plastic bottle that may be housed in a basket or box?
  • Acidic pH corresponds to which range?
  • Which information must appear on hazardous materials shipping papers in transit?
  • Which of the following is NOT a dispersion pattern for cryogenic containers?
  • Which term describes rules or directives issued by administrative agencies that have authority to enforce them?
  • Outline the typical order of operations for hazmat medical decontamination of a patient.
  • Which statement best defines a Toxic Inhalation Hazard (TIH) and explains why TIH incidents require enhanced protection?
  • Which of the following is NOT one of the four major container types?
  • Placard color blue indicates which hazard?
  • What are the core differences between radiological hazards and chemical hazards in hazmat response?
  • Which phrase correctly lists the three strategic modes of operation?
  • Which term describes the change of state from solid to liquid?
  • The violent reaction that releases a great amount of heat and energy is known as which process?
  • Placard color yellow indicates which hazard?
  • Which division indicates no significant blast hazard?
  • Which radiation is a high-energy wave emitted from an unstable nucleus and does not consist of particles?
  • Which term describes the transfer of a hazardous material to people, equipment, or the environment in greater than acceptable quantities?
  • A container with 125 gallons is classified as which category?
  • Which of the following is NOT a component of the four steps to hazard recognition?
  • What is the standard system for the identification of hazardous materials for emergency response?
  • Which division is associated with Oxidizers?
  • Which of the following best describes cryogenic container stressors?
  • Which container type is typically used for gases in HazMat transport?
  • Pressure tanks have pressures of
  • Which parameter describes how quickly a hazmat will become airborne and potentially travel away from the release site?
  • Three strategic modes of operation are listed as which?
  • Carboys are commonly available in which capacity, with 5-gallon containers being more common?
  • Pressure relief devices are typically set to activate at what percentage of the tank's test pressure?
  • Which symbol indicates unusual reactivity with water?
  • Which detection tool provides pass/fail indications but is not continuous?
  • Which of the following factors influence the decision to evacuate nearby residents during a hazmat incident?
  • Which storage type is described as non-pressure atmospheric storage tanks?
  • TRACEMP is an acronym used to categorize hazards. Which of the following is NOT a TRACEMP category?
  • What is the primary objective of decontaminating a patient prior to medical care or transport?
  • Which system is the standard for identifying hazardous materials for emergency response?
  • Which division corresponds to very insensitive explosives?
  • Which of the following is a component of the four steps to hazard recognition?
  • Which detection method identifies certain chemical signatures but is limited by line-of-sight and interference?
  • In hazardous materials incident response, responders seek to control or limit the emergency to a given area without direct contact with the hazardous material. Which mode does this describe?
  • Which radiation is an electron or a positron emitted from an atom and can be stopped by a thick piece of plastic or a stack of paper, potentially causing skin burns?
  • Which hazard class includes corrosives that can burn skin and eyes on contact?
  • At sea level, the standard atmospheric pressure expressed in psi can be approximated as which value?
  • Which radiation involves the emission of a neutron from the nucleus and is effectively stopped by hydrogen-rich materials like concrete or water?
  • In hazmat response, what does TIH stand for?
  • What is the difference between absorption and adsorption in spill cleanup, and why does it matter for response?
  • The primary objective of defensive mode is to limit exposure by:
  • A pressure vessel designed for pressures higher than 40 psi is called what?
  • Which action should responders take when confronted with a suspicious device?
  • Where can you find the four-digit UN identification number in the ERG?
  • Why is decontaminated water treated as hazardous waste, and how should it be disposed?
  • What term is defined as the lowest temperature at which a combustible material ignites in air without a spark or flame?
  • Which mode focuses on limiting exposure by avoiding direct contact with the material?
  • Low pressure storage tanks have pressures in which range?
  • Which two-letter code indicates a simple asphyxiant?
  • In hazmat response, which group typically conducts offensive operations?
  • A gas with water capacity 1200 pounds is which category?
  • What term describes a material whose atomic nucleus spontaneously decays or disintegrates, releasing radiation?
  • What term encompasses a series of energy waves including ultraviolet, visible, infrared, microwaves, radio waves, and extremely low frequency radiation?
  • Which term describes the change of state from solid to gas?
  • What is the primary purpose of organizing the Safety Data Sheet (SDS) into 16 standardized sections?
  • Which of the following is NOT a route of exposure?
  • Which process is direct solid to gas?
  • Which of the following is a dispersion pattern for liquid holding containers?
  • Which division is designated for toxic gases?
  • Carboys are typically available in 20 gallons, but which smaller size is more commonly used?
  • Bulk solid is defined as mass greater than what pounds?
  • Which factors influence isolation/evacuation distances during a hazmat release?
  • Which division corresponds to flammable gases?
  • What is the purpose of a staging area in a hazmat incident, and how does it support operations?
  • Which of the following is a component of the four steps to hazard recognition?
  • Which term describes the change of state from vapor to liquid?
  • Which statement correctly differentiates a gas from a vapor?
  • In a decontamination process, what is the second step after gross decon?
  • Which statement best describes defensive mode in hazmat response?
  • Define hot, warm, and cold zone boundaries and the criteria for moving between zones.
  • How do labels on individual containers differ from placards on transport vehicles?
  • Which container type is used for small-volume liquids such as glass or plastic containers?
  • Which zone provides decontamination and support functions but is not the hot contamination zone?
  • Why is it important to suppress ignition sources during a hazmat release?
  • Which value lists the standard atmospheric pressure at sea level in psi?
  • Which division pairing correctly matches Organic Peroxides?
  • Why is chemical compatibility crucial when selecting absorbents and neutralizers for a hazmat spill?
  • Which radiation consists of a helium nucleus with a large mass and positive charge?
  • Responders should wear which PPE level commonly for an unknown gas hazard before identification?
  • What color indicates a toxic inhalation hazard?
  • Which radiation can cause skin burns due to beta particles?
  • How does the ICS form of command facilitate coordination between HazMat operations and firefighting?
  • Which of the following is NOT a TRACEMP category?
  • A liquid with volume 110 gallons is which category?
  • Which group typically performs offensive hazmat operations?
  • When containing a liquid spill near a body of water, which strategy list correctly reduces environmental impact?
  • A hazardous material has entered or potentially entered your body via the routes of entry. This is known as:
  • What is the standard placard size?
  • An Infectious Substances hazard is indicated by which placard color?
  • What is the difference between reactivity and stability in hazmat terms?
  • What is the EMS role during a hazmat incident, and how do EMS and HazMat teams coordinate?
  • Which description best defines offensive mode in hazmat response?
  • Which division corresponds to non-flammable non-toxic gas?
  • Placard color green indicates which hazard?
  • Which placard color is associated with nonflammable gas hazards?
  • Common signs of exposure to corrosive substances and to strong acids or bases.
  • Which pages in the ERG contain the name of the material?
  • What term refers to the perception of the surrounding environment and the ability to anticipate future events?
  • What is the purpose of UN/NA numbers on hazmat packaging, and how do responders use them?
  • What is the Packing Group, and how does it affect packaging requirements and hazard communication?
  • Which term describes the change of state from vapor to solid?
  • Which division corresponds to extremely insensitive explosives?
  • Which term describes the change of state from liquid to solid?
  • What are the three awareness level responsibilities?
  • Which instrument detects volatile organic compounds but may miss inorganic gases and requires calibration?
  • What are typical reasons for requiring both gross and technical decontamination before transport?
  • What is the correct APIE-T sequence for incident analysis and response?
  • Why are oxidizers dangerous to store near fuels, and what immediate action should be taken if an oxidizer is involved in a spill?
  • Which of the following is NOT a typical dispersion pattern for cryogenic containers?
  • Oxidizers are associated with which placard color?
  • Nonbulk solid is defined as mass less than what pounds?
  • How should responders identify and protect against explosive hazards at suspicious devices or containers?
  • In a Safety Data Sheet (SDS), hazard information is primarily found in which sections?
  • Which term describes the change of state from liquid to gas?
  • Which process is gas to solid?
  • In an incident involving an unknown gas released from a cylinder, the responders should first:
  • Which division covers Organic Peroxides?
  • Why is preventing environmental contamination near waterways a critical consideration?
  • If direct action against the hazard is necessary, which hazmat response mode is indicated?
  • After exposure to TIH or other toxic inhalants, which symptom may be delayed?
  • Which term best describes radiation that does not ionize matter and includes visible light and radio waves?
  • What is the basic sequence for handling a small, contained hazmat spill that does not involve TIH?
  • Which term best defines any substance or material that poses an unreasonable risk to health, safety, property, or the environment if not properly controlled?
  • Which volume threshold defines non-bulk liquids?
  • Which action is a typical awareness level responsibility?
  • What is a primary purpose for documenting air monitoring results in the incident log?
  • Responders who take aggressive, direct action against the hazard are operating in which hazmat response mode?
  • Which term defines packaging other than a vessel or barge in which materials are loaded with no intermediate containment?
  • Non-bulk gas is defined as water capacity less than what pounds?
  • During a hazmat incident, how should ventilation be managed inside a building to prevent spreading contamination?
  • Responders who focus on public protection actions and do not operate in other hazmat scenarios describe which mode?
  • Which of the following is one of the four steps to hazard recognition?
  • Placard color red indicates which hazard?
  • Cryogenic liquid tanks have pressures of
  • List the primary differences among Level A, Level B, and Level C PPE and when each is used.
  • What are the critical elements to document in an incident log for HazMat responses?
  • What information must hazard placards and labels convey, and what does a Class 3 label indicate?
  • Which of the following is a component of the four steps to hazard recognition?
  • A substance categorized as flammable gas is placed in which division?
  • If water-reactive materials are involved, what is the recommended precaution?
  • Which division is associated with projectile fragment hazards?
  • Which process is liquid to gas?
  • Which option is a correct example of Hazard Class 9 Miscellaneous Dangerous Goods?
  • Some new LNG tanks have capacities of which range?
  • Base pH corresponds to which range?
  • What is the first step in gross decontamination at the scene?
  • Which term describes the temperature at which a liquid fuel produces enough vapors to sustain combustion after ignition?
  • Which division corresponds to very insensitive explosives?
  • Which division is designated for a fire hazard?
  • Which personnel conducts offensive operations at a hazardous materials incident?
  • Placard color white indicates which hazard?
  • Neutral pH corresponds to which value?
  • Which PPE level is used for high visibility splashes or splashes with inhalation hazard but lower skin exposure risk?
  • Which division is Infectious Substances?
  • Which of the following is NOT a common stressor for cryogenic containers?
  • Which radiation consists of particles with large mass and a positive charge, and is the least penetrating among common radiation forms?
  • Which mode describes responders focusing on public protection actions and not operating in other hazmat?
  • What term describes a condition, substance, or device that can directly cause injury or loss and is the source of a risk?
Subscribe

Get the latest from Examzify

You can unsubscribe at any time. Read our privacy policy